Official Luthiers Forum! http://www-.luthiersforum.com/forum/ |
|
Reso coverplate machine screws? http://www-.luthiersforum.com/forum/viewtopic.php?f=10101&t=45286 |
Page 1 of 1 |
Author: | Ken Jones [ Fri Mar 06, 2015 2:01 pm ] |
Post subject: | Reso coverplate machine screws? |
Anybody have a source for these? Ken Jones Mountain Song Guitars |
Author: | Bob Shanklin [ Fri Mar 06, 2015 2:31 pm ] |
Post subject: | Re: Reso coverplate machine screws? |
Here is your screws http://www.resophonicoutfitters.com/category/018.html Bob |
Author: | Ken Jones [ Fri Mar 06, 2015 5:06 pm ] |
Post subject: | Re: Reso coverplate machine screws? |
Thanks for that link. It looks like the only one that would work are the slotted vintage Nationals, as I need the fine pitch machine screws, as opposed to the ones for wood bodies. Unfortunately, the Republic I need them for has a phillips head. I guess I could replace them all, but at $2 a pop, that's kinda pricey. The quest continues! Ken Jones Mountain Song Guitars |
Author: | Ken Jones [ Sat Mar 07, 2015 9:41 pm ] |
Post subject: | Re: Reso coverplate machine screws? |
Bump. Anybody else know where to get Phillips-head, fine-pitch reso machine screws? Ken Jones Mountain Song Guitars |
Author: | Clinchriver [ Sun Mar 08, 2015 6:35 am ] |
Post subject: | Re: Reso coverplate machine screws? |
Ken Jones wrote: Bump. Anybody else know where to get Phillips-head, fine-pitch reso machine screws? Ken Jones Mountain Song Guitars Try MSC direct or local. IF they don't have it they can get it. https://www.mscdirect.com/browse/Fasten ... d=12108705 |
Author: | Ken Jones [ Sun Mar 08, 2015 11:51 pm ] |
Post subject: | Re: Reso coverplate machine screws? |
If I knew the actual size and pitch, that would work, or McMaster-Carr for that matter. Ok, new question, anybody know the size and pitch of the aforementioned screws...? Ken Jones Mountain Song Guitars |
Author: | kfish [ Mon Mar 09, 2015 8:11 am ] |
Post subject: | Re: Reso coverplate machine screws? |
I used to know the size but I forgot. I called National a few years ago to get a solution for the stripped threads on a used Tricone I bought and Don Young was very helpful. I bought the screws directly from him. Or call Resophonic Outfitters. That $2.00 might be for a set of 9 screws. Janet Davis shows the SKU number, NCS-306 as a set of 9 supplied by Beard. Kent |
Author: | Bob Shanklin [ Mon Mar 09, 2015 12:56 pm ] |
Post subject: | Re: Reso coverplate machine screws? |
Ken, all the other screws at Reso Outfitters are sets, so I don't think they are charging 2 bucks a screw for the vintage Nationals. Bob |
Author: | Ken Jones [ Mon Mar 09, 2015 1:33 pm ] |
Post subject: | Re: Reso coverplate machine screws? |
Yes, good point Bob. I did finally managed to get a response from Frank at Republic resonators, and he said he would send me some replacements, so it's all good. Thanks for everyone's input. Ken Jones Mountain Song Guitars |
Author: | Bob Shanklin [ Mon Mar 09, 2015 5:26 pm ] |
Post subject: | Re: Reso coverplate machine screws? |
Glad it worked out for you, Ken. ![]() Bob |
Page 1 of 1 | All times are UTC - 5 hours |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |